Clik here to view.
Wheel Bearing Greaser Mod?
I have a 2010 rzr S 800 and tried using my new bearing greesers today only to realize the head on my grease gun was to big to get it fully seated on the zerk without hitting the cv shaft. Decided to...
View ArticleRZR 800 2013
Hi everybody, im new on this forum , my name is Francis, im buying a rzr 800 2013 and i have a little question , my question is: when i press the gas pedal.... the response are not faster... i need...
View ArticleOdd problem....RZR won't start
Hi all. Have a bit of a head scratching problem. Been having trouble starting my rzr. I've changed the fuel pump. Checked the spark plugs. They were black so replaced those as well. I was able to...
View ArticleLoose Rack vs EPS?
I have a lot of steering play in my 14 800 EPS. How can I tell if the problem is in the rack&pinion vs the EPS/linkage?
View ArticleBrake Pedal Travel
I got a lot of brake pedal travel. Got a hard pedal and working brakes. I cant find anything on adjustment. Any ideas.
View ArticleGarage Products Bushings?
What do you think about using Garage Products bushings Vs Polaris stock products? I just replaced the shock and rear bearing carrier bushings and anxious to see how well they work.
View ArticleTrans problem on 2008 800. Will 2009 parts work?
All of the trans parts seem to be for 2009+. Will this interchange with 2008? Not sure what I need yet for parts, was poking around on Polaris parts site - most of the 2008 trans parts are...
View Articleidles fine but won't rev up under load gets boggy
ok guys and gals I'm stumped. I have done the following to diagnose the problem its a 2011 800 rzr4 RGE no mods! only 3000km. belt got wet going across a river and left me stranded but i did wench it...
View ArticleClik here to view.
Door Latches
My driver door latch isnt locking - any replacement latches out there for the Polaris doors.? Attached Thumbnails
View Article14" wheels from a General
I've been searching here for a bit but can't find a definite answer. I want to replace the factory 12" wheels and tires with a set of 27x9x14 Dirt Commander tires and stock aluminum wheels from a...
View Article4500lb winch in a 2011 RZR 800?
Here is what I got: 2011 RZR 800 - mounting the winch in the frame in the standard location, not on the bumper. 4500 Polaris Winch - 3x6.6 inch bolt pattern A Motoalliance winch bracket that I think...
View Article2014 rzr 4 800 rear diff nut question
Ok guys and gals, I have heard everything about this rear pinion nut problem. My question is, does this effect every year of the 800 or by the last year did they get it resolved? I don't have an issue...
View ArticleNeed new camshaft rzr 4 800
I need to buy a new camshaft for my rzr 4 800. I see caltric on eBay sells them for 60 bucks and a polaris cam kit it around 320. I also thought about a webcam new cam not reground. I don't wanna cut...
View Article800 rzr roller cam setup
Anybody have a old s&s roller cam setup they'd wanna sell? Possibly would buy a nice 994 grind webcam shaft as well.
View Articlewiring diagram
im putting a 900xp regulator on my 800s and moving it to the rear. does anyone know where the positive and negative wires from the oem regulator go? theyre hot all the time so i need to disconnect em.
View ArticleClik here to view.
New owner, have a couple of questions.
Bought a used 08 800. Does anyone know what brand lift this is? Trying to figure out which axles I need.Attachment 501921Attachment 501929 Sent from my iPhone using Tapatalk Attached Thumbnails
View Article08 800 Frame question
Hey all I'm new to the forum, I was wondering if anyone could help me out. I purchase a 50" 08 RZR 800 for a great deal knowing that the lower arm mount tabs and rail on the passenger side got really...
View Article2011 rzr800 limp mode issue
2011 Rzr EFI runs great until CEL comes on, engine stutters like running on 1 cylinder. let off on throttle, CEL goes off and engine resumes smooth running. can't get an error code. Checked and...
View ArticleGrinds when shifting gears
I have a 2014 rzr 800 and it grinds when I shift gears. I looked at the belt and it looks good, I couldn't see any cracks. Do I need a new belt or do I have another problem?
View ArticleUtah Crankshaft Camshaft 800 rzr
Anyone ever use or hear of Utah Crankshafts cams for a 800 rzr? They have the stock S profile or one slightly larger, but the funny thing is when I called they said we don't grind these in house. I...
View Article